How to Build a Cold Frame

coldframe1

Get an early start on spring planting or extend your gardening season with this DIY cold frame. A type of “mini-greenhouse,” a cold frame built with a glass or plastic lid allows plants access to sunlight and traps heat to prevent cold weather from putting an early end to your new crops. Follow these simple steps to construct your own cold frame using just a few tools, lumber, and a reclaimed window frame. The addition of a temperature-sensitive foundation vent will keep air flowing without risking plant loss due to unexpected cold snaps.

coldframe2

You will need: reclaimed 24-inch x 48-inch window (check window replacement shops, thrift and antique stores) / 2-inch x 8-inch x 16-foot rough cedar plank / one foundation vent / twelve 4 1/2-inch lag screws / two 3 1/2-inch galvanized T hinges / 8 hinge screws / two 4-inch eye hook latches / tape measure / drill with pilot bit and screwdriver tip / circular saw / straightedge / c clamps / jigsaw

coldframe3

From cedar planks, measure and cut three 48-inch lengths, two 18-inch lengths and one 20-inch length. These will be used to construct a simple raised bed and a second-tier angled cap to which the hinged-lid window frame will be attached. This project uses a 24-inch x 48-inch reclaimed window, but may be adjusted to accommodate windows as large as a storm door by matching the box size to window size. A larger cold frame may benefit from the addition of a second vent.

coldframe4

Cut the 20-inch cedar plank diagonally from corner to corner. C clamps and a long straightedge can be used as a saw guide, but are not required. These two pieces are the sides and will support the lid at a sloping angle to maximize sunlight.

coldframe5

Measuring 1 inch from the long side of the two 48-inch planks, drill a hole at each marked point 3/4 inches from the short edge using a pilot drill bit. Using eight 4 1/2-inch lag screws (two at each corner), assemble bed by driving screws through prepared holes into two 18-inch sides to form a rectangular box. Make sure all corners are square and don’t overlap.

coldframe6

Mark a spot 1 inch from the top and bottom on the back of the second tier at each end, then drill a hole at each of the four marks 3/4 inches from the end using pilot bit. Attach the angled sides to the back of the second tier using 4 1/2-inch lag screws driven through the pilot holes you have made.

coldframe7

On the back of the cold frame, use a straightedge to mark a horizontal 8-inch x 15-inch rectangle with sides centered horizontally and two inches from the top edge for the foundation vent. The addition of a foundation vent will allow air to circulate during warm period and trap heat when temperatures drop below 40 degrees F.

coldframe8

Use a jigsaw to cut the hole for the foundation vent. Foundation vents are designed with spring-loaded mounts, allowing the vent to be inserted without the need for additional screws once the frame is complete.

coldframe9

At the midway point, drill pilot holes to attach 4-inch hooks and eye latches inside the frame at each end. The latches will hold the top and bottom tiers together when in use, but allows for easy disassembly. Window latches may also be used instead, if desired. With the lid removed, the bottom tier may be used as a raised bed during summer months and the lid stored until cold weather returns.

coldframe10

Using hinge screws, attach a hinge 6 inches from the corners of the window frame along one long edge.

coldframe11

Place the window frame on top of the angled tier so the hinged edge rests evenly with the back. Use remaining hinge screws to attach hinges to the cold frame.

coldframe12

Push the foundation vent into the prepared hole until it snaps into place. The passive vent will automatically open during warm weather and close when temperatures drop below 40 degrees F. A 30-inch dowel can be used to prop the lid open to take full advantage of warm weather and maximize air circulation, but this vent is an invaluable fail-safe.

coldframe13

This attractive cold frame is simple to build and easy to disassemble for warm-weather storage. Adding a cold frame to your gardening routine can extend the growing season by weeks and reduces the risk of plant loss when germinating seeds before the last frost date.

coldframe14

This sturdy cold frame is easy to disassemble and store during warmer months, but may be anchored in place using stakes driven into the ground at each inside corner for permanent placement.

coldframe15

Your cold frame may be filled with an appropriate soil mix like any raised bed or used to house potted plants or germination trays to protect established plants from harsh weather or to get an early start on spring planting.

Originally: How to Build a Cold Frame

Advertisements
This entry was posted in DIY and tagged . Bookmark the permalink.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s